need sum quick info

Post questions, thoughts or comments on anything English & European Ford related here.
Post Reply
reggie
Posts: 235
Joined: Sat Oct 20, 2007 9:38 am

need sum quick info

Post by reggie » Mon Nov 12, 2007 9:29 am

I will like to know if anyone knows the bolt pattern on A 1967 anglia 105e . I do nto have acess to a spear rim at the moment to check.. I am looking at some aftermarket wheels that came out of a 1967 Mustang the rims are 14X6 and the bolt pattern on the wheels are 4.25 or 4.50 .
Any ENFO will be greately appreciated..
Reggie
"god made Adam & Eve for a reason"

JAN
Posts: 159
Joined: Sun Oct 21, 2007 6:57 am
Location: Wigan, UK

Post by JAN » Mon Nov 12, 2007 12:15 pm

I'm pretty certain the pcd of all four-stud British Ford wheels is 4.25", except 100E/107E at 5.5"

User avatar
stanchfi
Site Admin
Posts: 893
Joined: Thu Mar 15, 2007 6:56 pm
Location: Indiana
Contact:

Post by stanchfi » Mon Nov 12, 2007 12:16 pm

I just measured the spare for my 1960, center to center on the bolt holes is 4.25

hope this helps

heheheheh...ENFO......nice

-James

reggie
Posts: 235
Joined: Sat Oct 20, 2007 9:38 am

hey man

Post by reggie » Mon Nov 12, 2007 4:36 pm

Thanks a lot Loks like am gonna place theese rims on my car
"god made Adam & Eve for a reason"

IFHP
Site Admin
Posts: 1574
Joined: Thu May 03, 2007 12:28 am
Location: Olympia, Washington

Technical Discussions

Post by IFHP » Tue Nov 13, 2007 8:14 pm

I am delighted that members were able to answer this question so quickly. It really shows that EnFoStuff is living up to its potential. However, dear members, in the future please try to post all technical discussions in the Technical Discussion section. It makes it easier for members in the future to navigate both sections.

Thank you, Michael

reggie
Posts: 235
Joined: Sat Oct 20, 2007 9:38 am

Re: Technical Discussions

Post by reggie » Thu Nov 15, 2007 9:48 am

IFHP wrote:I am delighted that members were able to answer this question so quickly. It really shows that EnFoStuff is living up to its potential. However, dear members, in the future please try to post all technical discussions in the Technical Discussion section. It makes it easier for members in the future to navigate both sections.

Thank you, Michael
Ok I will Thanks..
Reggie
"god made Adam & Eve for a reason"

Dave A
Posts: 160
Joined: Sat May 05, 2007 4:43 pm

Post by Dave A » Tue Mar 25, 2008 9:52 pm

Yes the bolt pattern on all 4 bolt Euro and American Fords are the same at 4 X 4 1/4". You will however find the American wheels to have more positive offset which moves the wheel outward closer to the fenders. This does in theory, place more load on the wheel bearings etc.

The Mazda based Fords like the 91 and newer Escort/Tracer and also the Probe & Festiva are different and do not fit.

angliagt
Posts: 765
Joined: Mon Jun 11, 2007 5:01 pm
Location: Roanoke,Virginia

Post by angliagt » Tue Mar 25, 2008 10:17 pm

Mustang 6 cylinder= 4 lug

Mustang V8 = 5 lug.

And remember,rear wheel drive,& front wheel drive
aren't correctly compatible.I saw a Fiesta w/ Rwd wheels -
-looked very wrong! Offset is different.

- Doug
Remember - Nobody EVER says "COOL PRIUS!"

Dave A
Posts: 160
Joined: Sat May 05, 2007 4:43 pm

Post by Dave A » Tue Mar 25, 2008 10:21 pm

Yes and the V8 Mustang was 4 lug until 1994.

IFHP
Site Admin
Posts: 1574
Joined: Thu May 03, 2007 12:28 am
Location: Olympia, Washington

Lugs

Post by IFHP » Tue Mar 25, 2008 10:33 pm

I think Doug is talking about Mustang/Falcon wheels from the Sixties. My five bolt Taunus 17M has Falcon/Mustang wheels on the front (I assume that they don't fit on the back).

Dave A
Posts: 160
Joined: Sat May 05, 2007 4:43 pm

Post by Dave A » Tue Mar 25, 2008 10:37 pm

AHH....my mistake.

Post Reply