steering linkage ???

xclusiv · Post by **xclusiv** » Mon Jul 06, 2009 3:36 pm

hi all... i was wondering if any of you have changed bushings on the steering linkage.. i want to rebuild mine.. i saw some idler arm bushing on ebay, so i bought them, but now i don't know what to do about the rest.. are the bushings the same for the pitman arm also? any help is welcomed .. thanks folks

angliagt · Post by **angliagt** » Tue Jul 07, 2009 7:42 pm

What car are we refering to?What model/year?
I have many of the factory parts books for reference.

- Doug

xclusiv · Post by **xclusiv** » Tue Jul 28, 2009 7:21 am

its a 4 door 67 cortina 1500.

Dave A · Post by **Dave A** » Wed Sep 30, 2009 7:07 pm

Yes they are the same bushings on the pitman arm as the idler arm. The ones on the pitman arm tend to wear out quicker than the idler ones. While apart, make sure the pitman and idler shaft is smooth. If rusty make sure you sand rust off before replacing the bushings. Lube bushings with a light grease before installing.

xclusiv · Post by **xclusiv** » Sat Oct 10, 2009 8:09 pm

Thanks so much... i really want to get my car up and running... i have another question, is there any place in the US where i might be able to find the capri 2.8 vented discs from? or is there something that it could be substituted for.. thanks again for all your help...
just incase anyone needed to change front strut inserts, 1984 celica/supra inserts work like a charm in mk2 strut bodies..

70CortinaGT · Post by **70CortinaGT** » Sun Oct 11, 2009 8:54 am

I got vented disc's for a Cortina on EBay . Also , '87 Nissan Maxima rear strut inserts work very well ...

xclusiv · Post by **xclusiv** » Sun Oct 11, 2009 9:34 am

i found them there also... shipping is a killer.. 87 max.. thanks for the info..

70CortinaGT · Post by **70CortinaGT** » Sun Oct 11, 2009 9:44 am

http://www.r1concepts.com/FORD/CORTINA/ ... tsPage.htm These are the ones I got...

Post by **peteleo** » Mon Oct 12, 2009 8:28 am

xclusiv,

The celica/supra inserts will only work on the early MK2 bearing top mounts as the later MK2 mounts were different.

Pete

joeyramone30 · Post by **joeyramone30** » Mon Oct 12, 2009 10:07 pm

Pete, please elaborate - how do you determine early from late?

Post by **peteleo** » Tue Oct 13, 2009 9:00 am

If you look in the Cortina C Master Parts and Illus Catalog section 30 you'll see an illus. for the early 9/66-8/67 F/sus. and 8/67 on F/sus.

The early mounts incorporated a bearing while the later mounts are coned rubber ( silent blocks in British ) with a large washer between the mount and flange. I would spray Lithium grease in that area otherwise the rubber will stick to the metal washer creating a little heavier steering.

As you can see from the illus. the early and late shock shafts are different even though the inserts are interchangeable in the strut housing and the top mounts will also interchange.

Just a reminder, the Cortina MK1 and early MK2 inserts will not interchange even though they look the same on top.

Pete

joeyramone30 · Post by **joeyramone30** » Wed Oct 14, 2009 5:55 pm

Pete,

Thanks, I was looking at the catalog and ignored the dates at the bottom - I was thinking the illus. on the left was a mk 1 - something I should have caught. So, any ideas on alternate struts for a '69 Corty?

Post by **peteleo** » Thu Oct 15, 2009 9:40 am

The early MK2 transition model with the pre-c/f is confusing. I had a late MK1 GT registered as a '67 model.

I would rebuilt the original susp. There is nothing close that would fit without mods. including the Ford Capri. You may find all the parts in the U.S. Another solution is to purchase Gaz shocks which are adjustable gas coil over struts. www.gazshocks.co.uk They also make struts for the Anglia 105E and Popular. Also www.superflex.co.uk for poly. susp. bushes.
T/C arms / T/R ends / idler bushes watch ebay or contact Graeme White of EnFord Spares in New Zealand.

Pete

xclusiv · Post by **xclusiv** » Fri Oct 16, 2009 8:46 pm

http://www.r1concepts.com/FORD/CORTINA/ ... tsPage.htm These are the ones I got...

these are vented rotors? what caliper did you use? thanks for the link..
i bought the complete deflex poly kit off ebay, its good, the bushings fit nicely.. worth the money..

i'm sorry i wasn't complete with my comment about the strut inserts.. you do have to make a small spacer. sorry all..

Post by **peteleo** » Sat Oct 17, 2009 10:45 am

I checked out the link for Cortina disc brakes. I don't think those are vented because they won't work with the original calipers. So that's a good question: Does someone sell after market calipers for vented Discs ?

They advertise : for 1967 1600 ( cross-drilled & slotted ) and below 1967 1600 exc. MK11. Why for only the '67.

All 1965-70 MK1/2 Cortina GTs had the same solid disc and P16 Girling calipers/pads.

Cortina MK1/2 deluxes uses a thinner disc and P14 calipers and two variations of pads. ( early Cortina 1200 had F/ drum brakes ).